News · News · Retro Gaming · Controllers & Accessories · Retro consoles
Bridge Makes Your Original N64 Controller Wireless, No Mods, for $39
Bridge is a two-part adapter that makes any wired N64 controller wireless without opening it up. How it works, Paks, latency, battery, and the $39, 200-unit December launch.
https://averagetechnerds.com/n64-bridge-wireless-adapter-frivolbit/

The N64 controller cord was never long enough. You sat on the floor two feet from the TV, and someone always tripped over it. My own fix is an extension cable that gets me about 10 feet back. Bridge goes after the same problem without the cable. It’s a small adapter from a solo developer that makes the controller you already own wireless. Nothing gets opened up, nothing gets soldered, and if you pull it out, you have the same wired controller you started with.
How does Bridge work?
It’s two small modules that stand in for the cord. The Controller Module takes the controller’s plug in its top port. The Console Module goes in the N64’s controller port, where the cord used to go. Your controller talks to its module like it always talked to the console, the module sends that over the air, and the console module hands it to the N64 as if nothing changed.
The clever part is where the Controller Module lives. It’s shaped to slide into the controller’s accessory slot, the one at the bottom of the middle grip where a Rumble Pak or Controller Pak goes. The module tucks away, and the cord wraps up behind it with the velcro tie in the box. A dedicated cord wrap is planned as an add-on at pre-order, too.
Pairing is a button on each module. Press them until both lights show the same colour, and that’s your pair. The colour sticks when you power off, so you do it once. Four friends? Run four pairs on one console, each on its own colour, across nine fixed channels so they shouldn’t step on each other.
Why not just buy a wireless controller?
You can. I have a couple of 8BitDo 64s, but I don’t really play on them. A new controller isn’t the one you grew up with, and that’s who Bridge is for.
One way to keep an original controller and lose the cord is surgery, with a mod kit like 8BitDo’s. You open it up, swap its board for a wireless one, and the cord is gone for good. Bridge leaves your controller alone. Unplug it from the module and plug it into the console, and it’s a wired controller again.
Why not just get an extension cable?
Honestly, that’s what I’d try first, and it’s what I use. A 6-foot extension like Retro-Bit’s is $9.99 on Walmart.com. It’s a plain cable, so there’s no battery, no pairing and no added delay, and your Rumble Pak and Controller Pak go in the slot like they always did. The Transfer Pak is less certain: one buyer says it wouldn’t work through another brand’s cable, so test yours before you count on Pokémon Stadium.
The cord is still on the floor, though. It’s just longer, and someone can still trip on it. So for most people, the cable wins against a $39 wireless adapter. Bridge only makes sense if you really have your heart set on going wireless with your original controller.
Is it fast enough?
On paper, easily. Frivolbit puts the added delay at under 3 milliseconds. For scale, Super Mario 64 runs at 30 frames per second, so a new frame shows up about every 33 milliseconds. Three milliseconds is a small slice of one frame.
The trick is doing less. It skips Bluetooth for its own link, sends only what the console needs, and checks the controller more often than the console asks. No one outside the company has measured it yet, so if you play Smash seriously, wait for someone to test it.
What happens to your Paks?
The Controller Module lives in the accessory slot, which is also where your Paks go. So something has to give.
The Rumble Pak still works. Put it in the slot like always, and let the Controller Module sit next to you instead. The Controller Pak gets a smarter answer: the Console Module pretends to be one and keeps your saves on itself. Got saves on a real Pak? Bridge copies them over to the Console Module. Just keep track of which module holds them.
Then there’s the gap. Rumble Pak and Controller Pak are on the list, and the Transfer Pak isn’t. That’s the adapter that lets Pokémon Stadium read your Game Boy team. If Pokémon Stadium is the reason you still own an N64, treat the Transfer Pak as unsupported until Frivolbit says otherwise.
What about batteries and updates?
One AAA in the Controller Module runs it for about 10 hours of play, and the Console Module doesn’t need one. When the battery runs low, both lights flash together. You probably have a AAA in a drawer, so a swap takes seconds instead of waiting on a charge.
The firmware updates over Bluetooth, with instructions promised before it ships. For a first run from one person, that’s a good sign. If a game or a third-party controller turns up a problem after launch, it may be fixable without sending anything back.
Will it work on an Analogue 3D or M64?
That’s the big question, and nobody has answered it yet. Frivolbit promises any wired N64 controller, original or third-party, and says nothing about the Analogue 3D or M64. Both the Analogue 3D and the M64 have four original controller ports, as I covered in my Analogue 3D vs M64 comparison, so it may well work there. If you’re buying it for one of them, wait for Frivolbit to confirm.
Who makes it, and when can you get one?
One person, and a project that waited a long time. Alex, the developer behind Frivolbit, lives in Michigan. He started Bridge about ten years ago, then life got busy and family came first, so it sat. Now it’s back. His test games were the ones you’d guess: Ocarina of Time, Super Mario 64, Pokémon Snap and, more than anything, Super Smash Bros.
They’re due soon. The first run is only 200, and there’s still no pre-order or exact date. Frivolbit’s site has a sign-up form for an email when it launches, so if you want one, sign up now.
On the shelf
Retro consolesSee the whole story →Nerd Alert
Your Turn
What are YOUR thoughts
What have your experiences been? Let us know.










